Product Overview
Luminor BLACKCOMB-HO 6.1 Crossover UV
For the ultimate in higher flow rates, then LUMINOR's BLACKCOMB-HO 6.1 line of "Residential Crossover" UV water treatment systems should be your choice. Installed in a large residence or in a light commercial application, continuous UV water quality monitoring is provided by the inclusion of a true 254nm discrete UV monitor. Using Teflon technology for reduced fouling, these sensors allow for the addition of a solenoid shut-off valve and a 4-20mA output allowing for remote monitoring or data logging. A colour user interface allows for easy visual identification of UV intensity, remaining lamp life and any error or fault codes as well as a monitoring of a full system diagnostic on start-up. The system even incorporates QR codes to access lamp change information and videos via web access. The controller's universal input, constant current electronic power source is housed in a splash-proof case and comes standard with a "future-proof" expandability port for future upgrades or options. Commercial grade, axial flow 316L stainless steel, single-end reactors allow for lamp change without the need to drain the reactor chamber. Reliable, industry proven, high quality low pressure, high-output (LP-HO) coated UV lamps offer a consistent output over their 10,000 hour life. Paired with LUMINOR's encrypted lamp key for increased protection and ease of use. Flow rates of 15, 38, 53, 95 & 150 lpm (5, 10, 15, 25 & 40 gpm), in both 120V or 230V applications (same UV ballast, different IEC power cord), are offered in the BLACKCOMB-HO 6.1 series of products. Also available in NSF Class B or NSF Class A.
Luminor BLACKCOMB-HO 6.1 Crossover UV Features
- Free Floating (no cable twist), Keyed-in-Place, 254nm Teflon Based UV Sensor (on 6.1 models) Continuously Measures and Displays UV Output (as a %)
- Colour Screen Controller with Lightlock for Protected Lamp Replacement, Includes QR Codes, Full Diagnostics & Warnings
- "Future Proof" Expandability Port for Future Upgrades and Options
- Axial Flow, 316L Stainless Steel Polished Reactors, Designed & Manufactured to ASME Pressure Vessel Standards
- User Friendly Bayonet Style Lamp Connector (quick 1/4 turn removal with no extra tools needed)
- Reliable, Industry Proven, Proprietary Low Pressure High-Output Coated UV Lamps with Ceramic Bases for Durability and Long Life (10,000 hours)
- Constant Current Electronic Controller (one controller for all LPHO units) in a Splash Proof Case, Fully Potted Ballast Virtually Eliminates Common Water Damage Issue
- Full Customization Available as an Option (language, home screen, phone number, QR codes, ect.)
Blackcomb-HO6.1, Residential Crossover UV Systems, UV monitored
| Model | LBH6-051 | LBH6-101 | LBH6-151 | LBH6-251 | LBH6-401 |
|---|---|---|---|---|---|
| Flow Rate @ 16 mJ/cm²* (US Public Health) |
8.0 gpm | 19 gpm | 27 gpm | 47 gpm | 78 gpm |
| 30 lpm | 72 lpm | 100 lpm | 180 lpm | 290 lpm | |
| 1.8 m³/hr | 4.3 m³/hr | 6.1 m³/hr | 11 m³/hr | 18 m³/hr | |
| Flow Rate 30 mJ/cm²* (Industry Std.) |
4.0 gpm | 10 gpm | 14 gpm | 25 gpm | 40 gpm |
| 15 lpm | 38 lpm | 53 lpm | 95 lpm | 150 lpm | |
| 1.1 m³/hr | 2.3 m³/hr | 3.2 m³/hr | 5.7 m³/hr | 9.1 m³/hr | |
| Flow Rate @ 40 mJ/cm²* |
3.0 gpm | 7.0 gpm | 11 gpm | 19 gpm | 31 gpm |
| 15 lpm | 38 lpm | 53 lpm | 72 lpm | 120 lpm | |
| 0.7 m³/hr | 1.6 m³/hr | 2.5 m³/hr | 4.3 m³/hr | 7.0 m³/hr | |
| Port Size | ½" MNPT | ¾" MNPT | 1" MNPT | 1" MNPT | 1½" MNPT |
| Electrical | 90-265V / 50-60Hz | ||||
| Plug Type | American: Nema 5/15 - "1" suffix (i.e. LBH6-101) European: CEE 7/7 - "2" suffix (i.e. LBH6-102) British Standard: BS 1363 - "3" suffix (i.e. LBH6-103) Australian/New Zealand: AS/NZ 3112 - "4" suffix (i.e. LBH6-104) |
||||
| Lamp Watts | 18 | 34 | 45 | 67 | 101 |
| Power (watts) | 20 | 38 | 57 | 73 | 115 |
| Chamber Material | 316L Stainless Steel, A249 Pressure Rated Tubing, Polished & Passivated | ||||
| Replacement Lamp | RL-210HO | RL-330HO | RL-420HO | RL-600HO | RL-950HO |
| Replacement Sleeve | RQ-210 | RQ-330 | RQ-420 | RQ-600 | RQ-950 |
| Reactor Dimensions | 3.5 x 11.7" (8.9 x 29.8 cm) |
3.5 x 16.5" (8.9 x 41.8 cm) |
3.5 x 20.0" (8.9 x 50.8 cm) |
3.5 x 26.9" (8.9 x 68.3 cm) |
3.5 x 40.7" (8.9 x 103.4 cm) |
| Controller Dimensions | 8.6 x 4.2 x 3.5" (217.4 x 107.5 x 88.7 mm) | ||||
| Maximum Operating Pressure | 10.3 bar (150 psi) | ||||
| Operating Temperature Range | 2-40° C (36-104° F) | ||||
| UV Monitor | Yes | ||||
| Dry Contacts (solenoid ready) | Optional | ||||
| 4-20 mA Output | Optional | ||||
| Lamp Age Counter | Yes | ||||
| Lamp-Out Indicator (audible & visual) | Yes | ||||
| Shipping Weight | 4.5 kg (9.9 lbs) | 5.4 kg (11.9 lbs) | 6.0 kg (13.2 lbs) | 7.3 kg (16.1 lbs) | 9.8 kg (21.6 lbs) |
| *Note: | Flow rate for a given dose is calculated based on system output at end of lamp life in water with 95% UVT | ||||
LIMITED WARRANTY STATEMENT
Products manufactured by LUMINOR Environmental Inc. (LUMINOR) are warranted to the original user only to be free of defects in material and workmanship for a period as specified below. This warranty only applies to the original purchaser and is not transferable.
UV SYSTEMS
Ten (10) year Limited Warranty on the stainless steel reactors, from the date of original purchase, or installation (proper documentation required for verification).
UV LED SYSTEMS
GLACIER UV LED modules are covered by a One (1) year Limited Warranty, from the date of original purchase (proper documentation required for verification)
ELECTRONICS
Three (3) year Limited Warranty on the ballasts and controllers, from the date of original purchase, or installation (proper documentation required for verification).
UV LAMPS, UV SENSORS & QUARTZ SLEEVES
One (1) year Limited Warranty on all LUMINOR ultraviolet lamps, from the date of original purchase, or installation (proper documentation required for verification).
LUMINOR warrants that it will repair, replace or refund, at LUMINOR’s sole option, any ultraviolet system or component that is defective in materials or workmanship for the period as outlined above, subject to the “Limitations of Warranty” as outlined below. LUMINOR's liability under this warranty shall be limited to repairing or replacing at LUMINOR's option, without charge, F.O.B. LUMINOR’s factory or authorized service depot, any product that LUMINOR manufactures. LUMINOR will not be liable for any costs of removal, installation, transportation, or any other charges which may arise in connection with a warranty claim. Products which are sold but not manufactured by LUMINOR are subject to the warranty provided by the manufacturer of said products and not by LUMINOR’s warranty. LUMINOR will not be liable for damage or wear to products caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or repair, or if the product was not installed in accordance with LUMINOR’s printed installation and operating instructions.
LIMITATIONS OF WARRANTY
This warranty does not apply to any of the following:
- Water Quality Parameters lie outside of the following range:
- Hardness 120 mg/L (7 gpg)
- Iron 0.3 mg/L (ppm)
- Manganese 0.05 mg/L (ppm)
- Tannins 0.1 mg/L (ppm)
- Turbidity 0.1 NTU
- Transmittance (UVT) 75% (50% for Low-UVT systems)
A product that has been incorrectly installed according to the technical installation manual.
A product that has been modified in any manner, unless approved by the manufacturer.
A product where the serial number has been altered defaced or removed.
Damage caused by the use of parts that are not compatible, suitable and/or authorized by LUMINOR for use with the product (e.g. non-original lamps or sleeves).
Damage caused during shipment of the product.
Water damage is found inside ballast housing or controllers.
Product is installed outdoors in direct contact with the environment (rain).
Product is installed in freezing temperatures.
Product is used in conditions that exceed LUMINOR’s specifications.
TO GET WARRANTY SERVICE
To obtain service under this warranty, you must first contact LUMINOR Customer Service at 855-837-3801 (519-837-3800 outside of the US or Canada) to obtain a Warranty Return Authorization.
You will then need to return the product through the LUMINOR Dealer or Distributor where the product was originally purchased, together with proof of purchase and installation date, failure date, and supporting installation data. Unless otherwise provided, the Dealer or Distributor will contact LUMINOR for instructions on returning the product. Any defective product to be returned to LUMINOR must be sent freight prepaid; documentation supporting the warranty claim and/or a Return Material Authorization must be included if so instructed.
LUMINOR WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES, OR EXPENSES ARISING FROM INSTALLATION, USE, OR ANY OTHER CAUSES. THERE ARE NO EXPRESS OR IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND THOSE WARRANTIES DESCRIBED OR REFERRED TO ABOVE.
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY MADE BY LUMINOR WITH RESPECT TO THE PRODUCT, AND IS GIVEN IN LIEU OF ANY OTHER WARRANTY. TO THE EXTENT ALLOWED BY APPLICABLE LAW, ANY AND ALL EXPRESS OR IMPLIED WARRANTIES NOT SET FORTH HEREIN ARE WAIVED AND DISCLAIMED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. LUMINOR LIABILITY UNDER THIS LIMITED WARRANTY IS LIMITED SOLELY TO THOSE LIABILITIES SET FORTH ABOVE. IN THE EVENT THAT ANY PROVISION OF THIS LIMITED WARRANTY SHOULD BE OR BECOME INVALID OR UNENFORCEABLE UNDER APPLICABLE LAW, THE REMAINING TERMS AND CONDITIONS HEREOF SHALL REMAIN IN FULL FORCE AND EFFECT AND SUCH INVALID OR UNENFORCEABLE PROVISION SHALL BE CONSTRUED IN SUCH A MANNER AS TO BE VALID AND ENFORCEABLE.
